Type CSA (75 PSI to 2000 PSI)
Type CSA & CSB Bearings
This blend (CSA) was formulated for use against itself as a slide material.
The CSA system consists of an upper and lower element. The PTFE slide surfaces in this system are nominally 3/32" thick and are control-bonded to a 10-gauge carbon steel (CS) back up sheet. Normally the upper element is larger than the lower element by the amount of anticipated movement.
The blended CSA material used for this bearing is composed of virgin (unreprocessed) PTFE resin tested per ASTM D4894 or ASTM D4895 and reinforcing agents including milled glass fibers. This structural material has the following representative mechanical and physical properties:
The design engineer shall determine the square inches of bearing area required for the lower element by dividing the load by the allowable pressure from the graph. The upper element is sized for the movement after the lower element is sized for load.
CON-SERV Inc can supply any practical size cut from stock steel. Size is out to out of back-up plate.
For ease of installation, CON-SERV recommends a back-up plate 1" larger than the CSA or CSB size to allow a 1/2" recess all around. This recess must be provided for plates requiring a seal weld.
Certifications on the epoxy, steel and CSA material are available upon request.
The CSA system consists of an upper and lower element. The PTFE slide surfaces in this system are nominally 3/32" thick and are control-bonded to a 10-gauge carbon steel (CS) back up sheet. Normally the upper element is larger than the lower element by the amount of anticipated movement.
The blended CSA material used for this bearing is composed of virgin (unreprocessed) PTFE resin tested per ASTM D4894 or ASTM D4895 and reinforcing agents including milled glass fibers. This structural material has the following representative mechanical and physical properties:
- Tensile Strength: 2200 psi
- Elongation: 225%
- Specific Gravity: 2.17-2.22
The design engineer shall determine the square inches of bearing area required for the lower element by dividing the load by the allowable pressure from the graph. The upper element is sized for the movement after the lower element is sized for load.
CON-SERV Inc can supply any practical size cut from stock steel. Size is out to out of back-up plate.
For ease of installation, CON-SERV recommends a back-up plate 1" larger than the CSA or CSB size to allow a 1/2" recess all around. This recess must be provided for plates requiring a seal weld.
Certifications on the epoxy, steel and CSA material are available upon request.
Item # |
Slide Surface Thickness |
Slide Surface Material |
Back-Up Plate Thickness |
Back-Up Plate Material |
Quantity |
---|---|---|---|---|---|
CSA Lower 06CSA 75CT | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 3/4" PL | Back-Up Plate Material N/A Corten Steel | |
CSA Lower 06CSA 50CT | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Corten Steel | |
CSA Lower 06CSA 37CT | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 3/8" PL | Back-Up Plate Material N/A Corten Steel | |
CSA Lower 06CSA 25CT | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 1/4" PL | Back-Up Plate Material N/A Corten Steel | |
CSA Lower 06CSA 13CT | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 10 GA | Back-Up Plate Material N/A Corten Steel | |
CSA Upper 06CSA 100CT | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 1" PL | Back-Up Plate Material N/A Corten Steel | |
CSA Upper 06CSA 75CT | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 3/4" PL | Back-Up Plate Material N/A Corten Steel | |
CSA Upper 06CSA 50CT | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Corten Steel | |
CSA Upper 06CSA 37CT | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 3/8" PL | Back-Up Plate Material N/A Corten Steel | |
CSA Upper 06CSA 25CT | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 1/4" PL | Back-Up Plate Material N/A Corten Steel | |
CSA Upper 06CSA 13CT | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 10 GA | Back-Up Plate Material N/A Corten Steel | |
CSA Lower 06CSA 100SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 1" PL | Back-Up Plate Material N/A Stainless Steel | |
CSA Lower 06CSA 75SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 3/4" PL | Back-Up Plate Material N/A Stainless Steel | |
CSA Lower 06CSA 50SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Stainless Steel | |
CSA Lower 06CSA 37SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 3/8" PL | Back-Up Plate Material N/A Stainless Steel | |
CSA Lower 06CSA 25SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 1/4" PL | Back-Up Plate Material N/A Stainless Steel | |
CSA Lower 06CSA 13SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 10 GA | Back-Up Plate Material N/A Stainless Steel | |
CSA Upper 06CSA 100SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 1" PL | Back-Up Plate Material N/A Stainless Steel | |
CSA Upper 06CSA 75SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 3/4" PL | Back-Up Plate Material N/A Stainless Steel | |
CSA Upper 06CSA 50SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 1/2" PL | Back-Up Plate Material N/A Stainless Steel | |
CSA Upper 06CSA 37SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 3/8" PL | Back-Up Plate Material N/A Stainless Steel | |
CSA Upper 06CSA 25SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 1/4" PL | Back-Up Plate Material N/A Stainless Steel | |
CSA Upper 06CSA 13SS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 10 GA | Back-Up Plate Material N/A Stainless Steel | |
CSA Lower 06CSA 100CS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 1" PL | Back-Up Plate Material N/A Carbon Steel | |
CSA Lower 06CSA 75CS | Slide Surface Thickness N/A 1/16" | Slide Surface Material N/A CSA | Back-Up Plate Thickness N/A 3/4" PL | Back-Up Plate Material N/A Carbon Steel |